The operation manual for PCB cutting machine and PCB depaneling equipment troubleshooting (ASC-710N-160 model)

PCB depaneling machine with the width changeover devise that can through the cylinder expansion principle to control the fix tray to achieve the fast changeover the PCB width.
 
When your PCB board with different V-cut width, use this type PCB cutting machine can changeover the cutting width quickly, can greatly to save your more time for depaneling operation. For example, if you PCB board with the PCB edge,use the standard PCB separator, you need manual to adjust the fix tray to suitable for your PCB edge width and your PCB stripes width again and again. This type machine can help you avoid the repetitive adjustment operation and avoid the wrong happen during your adjustment.   



PCB cutting machine
 
 
The PCB cutting machine width adjustment range: 0-160mm, you can set the PCB changeover width according your pcb edge width and the PCB stripes width.

Pleae check the following step to set the machine changeover width:



The PCB-A and PCB-B width less then 80mm,the PCB separator adjustment as the following:




At first: confirm the cylinder back to the zero position.
 
1)Connect the air for the PCB cutting machine
2)Confirm the cylinder whether run to the zero position
3)If the cylinder is not in zero position, adjust the rotary knob to let the cylinder back to the zero position
 
After adjustment, please open the hand valve, confirm the 2 group of cylinder keep stop move state.
 
 
At second: the process for let the blade fix the PCB of PCB depaneling equipment
 
A.Loose the 3th blade knob and let the 3th blade move down and suitable for fix the PCB board.
B.Place the PCB into the cutting group of PCB separator
 
 
At third: the process for PCB width adjustment
 
Setting the small PCB width as the PCB-A sample, setting the big PCB width as the PCB-B sample, must adjust the big PCB width first and then adjust the small PCB width.
 
A. Open the A hand valve, and Adjust the right and left A cylinder to the Max.extrusion
B. Loose the right and left handle screws and move the cylinder until touch the PCB
C. When A cylinder touch PCB and then tighten up the hand screws.
D. Open the A hand valve over and over again to confirm the PCB-A width is ok.
E. Now is finish the PCB-A sample width adjustment, and start adjust the PCB-B
F. Put the PCB-B sample into the machine,and adjust the B hand valve to control the right and left B cylinder,
G.When the fix plate touch the PCB-B, the adjustment is finish.
H.Open the B hand valve over and over again to confirm the PCB-B width is ok.
I. Only need to open the B hand valve these 2 type PCB width.
J. Adjust the cutting group and try to do the PCB board cutting operation.



The PCB-A and PCB-B width more then 80mm,the PCB separator adjustment as the following:

 
At first: confirm the cylinder back to the zero position.

1)Connect the air for the PCB cutting machine
2)Confirm the cylinder whether run to the zero position
3)If the cylinder is not in zero position, adjust the rotary knob to let the cylinder back to the zero position
 
After adjustment, please open the hand valve, confirm the 2 group of cylinder keep stop move state.
 
Setting the small PCB width as the PCB-A sample, setting the big PCB width as the PCB-B sample, must adjust the big PCB width first and then adjust the small PCB width.
 
At second: Place the PCB into the cutting group of PCB depaneling equipment.
 
A.Loose the 3th blade knob and let the 3th blade move down and suitable for fix the PCB board.
B.Place the PCB into the cutting group of PCB separator

 
At third: the process for PCB width adjustment
 
Setting the small PCB width as the PCB-A sample, setting the big PCB width as the PCB-B sample, must adjust the big PCB width first and then adjust the small PCB width.
A. Open the A hand valve, and Adjust the right and left A cylinder to the Max.extrusion
B. Loose the right and left handle screws and move the cylinder until touch the PCB
C. When A cylinder touch PCB and then tighten up the hand screws.
D. Open the A hand valve over and over again to confirm the PCB-A width is ok.
E. Now is finish the PCB-A sample width adjustment, and start adjust the PCB-B
F. Put the PCB-B sample into the machine,and adjust the B hand valve to control the right and left B cylinder,
G.When the fix plate touch the PCB-B, the adjustment is finish.
H.Open the B hand valve over and over again to confirm the PCB-B width is ok.
I. Only need to open the B hand valve these 2 type PCB width.
J. Adjust the cutting group and try to do the PCB cutting operation.



If you have more question about the PCB cutting machine or the pcb depaneling equipment troubleshooting ,Please sent the email to : info@ascen.ltd , we will feedback you in one days .